Beskrivelse
STP-SE
Looking for an elite pre-amp designed for the most critical listener? Look no further than our STP-SE. The ‘SE’ stands for special edition and as our customers and reviewers will tell you, this piece of equipment is special, indeed.
The STP-SE’s stellar performance and upgrades begin with its wires: Kimber Kable’s patented TCSS wiring, a highly passive multi-gauge, multi-strand, continuous strand pure copper that allows for greater dielectric movement than most other wires in its class. Add to that four oversized power-supply capacitors replaced with our trademark Low ESR “Super Cap,” an extremely low noise floor (<6µV Passive, <18µV active) and a fully balanced circuit and the results are spectacular 3-D imaging and instrument placement.
A 25A Schottky bridge rectifier connected through 164,560+µF of capacitance via our proprietary TRR (Triple-Ripple-Reduction) power supply circuit ensures exceptionally clean power delivery to optimize audio quality. Standard operation in a passive state and gain to boost the signal only when needed brings you the utmost fidelity. The STP-SE’s resistor ladder volume control, built with our discrete proprietary design, guarantees the STP-SE’s volume control is clean, accurate, and transparent.
Our available Stage 1 STP-SE upgrade features our discrete proprietary regulators along with 24 Vishay Z-Foil resistors, four premium inductors, four Schottkey diodes and a Rhodium-plated Furtech fuse. These enhancements which focus on the power supply and input/output buffer circuits present greater fidelity and definition.
The Stage 2 upgrade, includes all of the above plus a Furutech rhodium plated IEC inlet, 48 Vishay Z-Foil resistors located in the resistor ladder volume control, 16 upgraded high frequency filter capacitors and a green OLED display. Direct attention to the signal path throughout the volume control and filtering circuit yields major enhancements to an already exceptional product.
Standard STP-SE Features
- Input / Output wiring upgraded to Kimber Tcss wire
- 2nd stage filtering caps (4-22,000uf caps) are upgraded to the Wyred 4 Sound Low ESR “SUPER CAP” designed for power supplies
- Vacuum Fluorescent Display (VFD)
- Optical rotary encoder (volume knob)
- Fully functional remote control
- 12V DC Trigger input (to automatically activate HT Bypass mode)
- Two – 12V DC Trigger outputs
- Home Theater bypass (customizable for any input, also DC Trigger input selected)
- Balance control
- Absolute phase control (0°/180°)
- Efficient (no heat)
- Tripple-ripple reduction circuit contains 164,560uF of capacitance
- Extremely low noise floor
- Fully balanced input to output
- Buffered passive/active design
- Automatically switched in Line Stage (when more volume is needed)
- Discrete volume control using dale RN55d resistors
- Unbalanced to Balanced conversion (when RCA input selected and XLR outputs are being used)
- Idle power consumption = 15w
- Rugged construction
- ½” Machined and Anodized front panels
- 60kΩ input impedance
- 3 sets of gold plated unbalanced (RCA) inputs
- 2 sets of gold plated unbalanced (RCA) outputs
- 2 sets of Neutrik Balanced (XLR) inputs
- 2 sets of Neutrik Balanced (XLR) outputs
- Factory Selectable mains 115/230VAC
- Compact size (17”W x 4”H x 13”D)
- 22 lbs.
- Covered by a 5 YEAR WARRANTY
Stage 1 Upgrade Adds…
- Upgraded fuse
- 4 Schottkey diodes
- 4 premium inductors
- W4S discrete regulators
- 24 Vishay Z-Foil resistors
Stage 2 Upgrade Adds…
- All upgrades in Stage 1
- Furutech rhodium plated IEC inlet
- 48 Vishay Z-Foil resistors located in the resistor ladder volume control
- 16 upgraded high frequency filter capacitors
- Green OLED display
Note: Due to the expensive specialty parts as well as the extensive labor involved with the upgrade, Stage 1 and Stage 2 STP-SE orders are non-refundable.